Sold Items
Wanted
Any high performance or racing type part for Datsuns/Nissan. Let us know what you have to sell or trade. Anything for body or drivetrain.Sold Items
All items listed below have been sold. This is just a partial list.
Please contact us with any items you are looking for.
All items listed below have been sold. This is just a partial list.
Please contact us with any items you are looking for.
KA24E 12 valve Dual sidedraft setup W/Competition prepped Mikuni 44's with insulators, c'pull linkage, air horns,
-6 fuel inlets, et al. Perfect setup for street or race, originally setup for GT3 KA24E............................... .... ...SOLD
QuarterMaster 7 1/4" Clutch Dual disc complete less friction disks,WITH 6 bolt 93 tooth FLYWHEEL, nearly new w/aluminum Comp Cover .... ...SOLD
HKS Lightweight Steel Flywheel, 8 Lbs. 6 Bolt, 225mm friction surface. Excellent shape for L20B or any L6 engine in Z-car. ...SOLD
Complete set of 8 NOS Nissan Motorsports Competition Valve Springs, inner & outer, 280 lb/in, 1 3/4" OD, assembled height
is 1.720" with coil bind @ .970", 99996-M1046, cryo-treated and REM-ISF finished for extra strength and oil shedding ...... ...SOLD
Complete set of 12 NOS Nissan Motorsports Competition Valve Springs, inner & outer, 280 lb/in, 1 3/4" OD, assembled height
is 1.720" with coil bind @ .970", 99996-E1046, cryo-treated and REM-ISF finished for extra strength and oil shedding ...... ...SOLD
Nissan Motorsports Comp Header for the L16/L18 in a Datsun 510. Beautiful construction, 1 5/8" tube 2 1/2" collector,
not chromed, brand new, unused (can be used with L20B with a raised floor).................................... ...SOLD
R180 4.38 Welded Diff no side flanges. Gone thru and setup by Jasen Jasensky of Bob Sharp fame.
Done the right way. Never used, new bearings, seals et al. 4 side gears welded for extra strength....... ...SOLD
Nissan Motorsports Close Ratio O/D Tranny # 32010-E8752 - This is Brand new, never used, Servo Steel
Syncro Motorsports Tranny with flange output. Long Tail B-style shifter, forerunner to Current Motorsports
CR tranny (32010-N3200) that uses Warner Syncros. 2.906, 1.902, 1.308, 1.000, .864. ......... ....SOLD
Quaife R180 ATB Torque Biasing differential, 115MM ID Late R180, Excellent used shape, 1 Auto-X season
R180 (240-280Z) 115mm ID ring gear [4spd 8/76>] Quaife # 44.309.141 -
THIS IS THE CENTER SECTION ONLY .......List for $1,345.00................................................. ............ ....SOLD
Z20/Z22/Z24 Cannon Dual Sidedraft manifold w/o Linkage...................................................................... ........ ....SOLD
40/45 mm Mikuni Short double sidedraft manifold for 510 w/ linkage............................................................. .. . ...SOLD
40/45 mm Datrally manifold from Australia for 4 cylinder, nice, strong, thick runners for strength and porting..... .. . ...SOLD
L6 ARE Drysump pan with windage tray, -12 fittings, excellent used condition..($569 list)............. .. . ...SOLD
We now have a new Comp Dept style L-series Damper with Special bolt and washer combo Single groove v-belt
SFI Approved with latest tech elastomer, must use Z-car water pump and pulley................. .. . ...SOLD
Original Electromotive crankfire ignition kit for 4 cylinder or 6 cylinder L16/L18 or 6 cylinder L series Datsun motors.
In excellent used condition. Kit includes MSD 7AL Ignition box, Mallory Coil, freshly painted timing cover with mounting
tab and magnetic pickup. 4 or 6 cyl. style reluctor wheel included. Original Nissan Comp part # 99996-E2100.. .. . ...SOLD
V912 Closed Chamber Factory Race Head, NOS in Factory Cosmoline and Box. 99996-V9182
Cam towers, no cam, no valves...Factory List $834...................................................................................... .. . ...SOLD
QuarterMaster 7 1/4" Clutch Single disc complete,WITH 5 bolt 93 tooth FLYWHEEL, nearly new w/aluminum Comp Cover.. ...SOLD
QuarterMaster 7 1/4" Clutch Dual disc complete,WITH 5 bolt 93 tooth FLYWHEEL, nearly new w/aluminum Comp Cover. ...SOLD
R 160 – 4.63 Ring & Pinion only, excellent used shape........................................................................ ...SOLD
R180 4.38 Open Diff Complete ……………....................................................................................... ....SOLD
TRIPLE Taper Bored 44’s ON AN (another!!) ORIGINAL, UNMOLESTED, UNUSED, NOS, DATSUN
COMPETITION L6 MANIFOLD WITH ALL NEW EVERYTHING!! These 44’s are Stage 3 Competition
Prepped with Taper Bores, Thinned Throttle Shafts and all the internal float chamber modifications for fuel
management……………..The penultimate race setup, especially for vintage… .....SOLD
Datsun 510 Dual Mikuni Sidedraft setup for the L-series 4 cylinder
A completely refurbed dual sidedraft setup for the L-series 4 cylinder motor on a Black Gloss Powder Coated Mikuni Short Manifold.
Black Powder Coated Air horns with Brand New ITG Filter with Black Powder coated backplate . Hot Looking setup.. .....SOLD
Cam Tech 420-02 6 Cylinder Race cam & matching rockers, excellent used shape................................ ............SOLD
L6 Datsun Comp Gated/Winged Extra Capacity wet sump pan with External Pump Pickup............... ............SOLD
A Pair of NOS (New Old Stock) 50's, Brand New!! Never Used.....with standard side linkage......... .........SOLD
A87 Closed Chamber head w/o valves and springs NOS brand new in Nissan box........................................ .........SOLD
R180 4.38 LSD Diff Complete w/ U-joint Side Flanges ........................................ .......................SOLD
R180 LSD Center Section 110mm ID Ring gear pilot, good shape, ready to install........................................ .......................SOLD
R180 4.11 Open Diff Complete …………….................................…..................................................... .......SOLD
Set of 3 Arias Forged/domed pistons for L20B - 86MM Nismo Part # 99996-K1010B w/pins& rings Brand new.. ............SOLD
Deves Ring set for L20B 86mm (+.040) 99996-D1077 new....................................................................... ........................SOLD
Nissan Competition/ Rebello V912 ported/polished head, SI Stainless valves, 44mm intake, 35mm exhaust. 14.5:1 compression.
Rebello GT4 Spec .600” Lift cam. Larger Comp race valve springs & custom Titanium retainers. Lightened/balanced rockers,
2 Weekends total ........................................................................ .......SOLD
Set of SI tuliped/swirled valves for 4 cylinder L-series 44mm intake/38mm Exhaust..NEW ............................... ......SOLD
Rebello L16 GT4 - Motor #2
Ex David Walsh GT4 Spec long rod L16. V912 ported/polished head, 44mm intake, 35mm exhaust. 14:1 compression.
Rebello GT4 Spec cam. Isky race valve springs & retainers. SI Stainless valves. Lightened/balanced rockers, valve cover cam oiler.
5.75” Carillo’s , J&E Pistons. Ground, polished, shot- peened crank. Billet center main cap with grade 12.9 main cap bolts.
Setup for drysump but can be switched to external pickup wetsump pan. Crank Triggered but could easily be changed over.
Rebello Dyno sheet shows 203 HP and 144 Tq . 5 hours total time..............................................................................SOLD
QuarterMaster 5 1/2" Clutch Dual disc complete,WITH 5 bolt 93 tooth FLYWHEEL, excellent shape w/aluminum Comp Cover...$ SOLD
Rebello L16 GT4 - Motor #1:
*** Ex David Walsh GT4 Spec Long Rod L16. V912 ported/polished head, SI Stainless valves, 44mm intake, 35mm exhaust.
14.5:1 compression. Rebello GT4 Spec .600” Lift cam. Larger Comp race valve springs & custom Titanium retainers.
Lightened/balanced rockers, valve cover cam oiler. 5.75” Carillo’s , J&E Pistons. Fully counter-weighted, knife-edged ground,
polished, shot- peened crank Billet center main cap with grade 12.9 main cap bolts. Setup for drysump but can be switched to
external pickup wetsump pan. Crank Triggered but could easily be changed over.
Rebello Dyno sheet shows 215 HP and 150 Tq . Dyno Time only. ........................................SOLD
**
Nissan/Datsun L28 Race Motor #2: 2.8L motor has J&E pistons and Carillo rods
with Stock, race prepped and cryo -treated crank, 13.5:1 compression. Abacus Racing head, SS valves and Cam Tech 420-02
(specs on dyno sheet) cam. ARE dry sump pan. Total time of 1 race weekend ........ . . .. SOLD
THE LAST SET OF NOS ( NEW OLD STOCK )TRIPLES YOU WILL EVER FIND. COMPLETELY BRAND NEW,
STAGE 3 COMPETITION PREPPED WHICH MEANS TAPER BORED BARRELS, FLOAT CHAMBER
MODIFICATIONS AND THINNED THROTTLE SHAFTS, -6AN FUEL FITTINGS.
3 BRAND NEW OLD STOCK 44MM CARBS, READY TO ROCK!!!!.......................... ....... . .. SOLD
A Pair of refurbed/Rebuilt 50's with air horns and standard side linkage....................................................... .. .. SOLD
40/44 mm TWM #0030 medium length triple sidedraft manifold for Z-car ................................................... .. SOLD
Original Unused Factory Fully Counterweighted 6 bolt Racing Crank for L16 SUPER RARE PIECE - NOS... ..SOLD
Set of 6 Arias Forged/Domed pistons for L28 - 87MM Nismo Part # 99996-N1010B w/pins, buttons
& rings Brand new... ......SOLD
TRIPLE 50’S (from above) ON AN ORIGINAL, UNMOLESTED, UNUSED, NOS, DATSUN COMPETITION
L6 MANIFOLD WITH ALL NEW EVERYTHING!! The ultimate race setup, especially for vintage… ......SOLD .
Nissan/Datsun L28 Race Motor #3: 2.8L over-bored with Winberg billet crank (fully counterweighted, designed by Auerbach). BRC coated pistons and Cunningham rods, 14.5:1 compression. Gerolamy head with additional flow improvements by Jeff Winter in Dec ‘05. Has Xceldyne Titanium valves and Electramotive spec L-3 cam. ARE dry sump pan. Nissan Motorsports harmonic balancer with water pump pulley and Electromotive pickup wheel for HPV-1 Ignition. Total time of 2 race weekends
Additional Pistons, Rods, Bearings and Titanium Valves as well as HPV-1 ignition are also available at additional cost. Reasonable Offers will be considered
Stahl Racing Stepped Header for Z-car L-Series 6 cylinder, 3 into 2 into1, Dyno Use only, ports for EGT... ......SOLD
Nissan/ Datsun L28 Stroker Race Motor #4: 3.0L Stroker with Stock, race prepped and cryo-treated LD28 Diesel crank. BRC coated pistons and Cunningham rods, 14.7:1 compression. Gerolamy head with additional flow improvements by Jeff Winter in Dec ‘05. Has Xceldyne Titanium valves and Auerbach spec L-3 variant cam with 112 degree lobe centers. ARE dry sump pan. Nissan Motorsports harmonic balancer with water pump pulley and Electromotive pickup wheel for HPV-1 Ignition. Total time of 1 race weekend ......SOLD
Additional Pistons, Rods, Bearings and Titanium Valves, Stock, race prepped and cryo -treated crank as well as HPV-1 ignition are also available at additional cost.
W53 JDM Closed Chamber head w/o valves and springs. Great Shape........................................................ ..... SOLD
Option 3 - 1st gear set......... 32310-E9601 Counter Shaft gear 18 tooth, 32343-E9611 Main Shaft Gear 28 tooth see pix ,........Magnafluxed good, excellent shape........will sell as a set only................................................... SOLD
BRE Manifold, original excellent shape with water tube - ( carbs not included) Own a piece of history for that 2.5 Trans Am racer !................................ See pix ...... See pix .............$ 500.00 .. ........ SOLD
R160 4.11 Open Diff complete w/ U-joint side flanges.......................................................................................... SOLD
13 X 9 Keizer 3 piece wheels......4 X 4 1/2" 3 1/2" Backspace...Set of 2 . Super lightweight........................ SOLD
R180 - 3.70 Ring & Pinion only, BRAND NEW, never setup 38100-78600................................................ SOLD
Complete GT4 Nissan L16- 12.5:1 compression motor w/ crankfire MSD pickup, V912 Gerolamy big valve hi-lift asymmetrical cam head w/ Nismo degreed cam sprocket, ARP Head Studs, DPR cam oiler spraybar, Cosworth domed Pistons, Total Seal rings, worked rods w/ARP bolts, Aviaid external pickup wetsump gated/winged pan w/Nismo external pickup pump cover and external pressure adjuster, ARP Main Studs, Tilton ULGC Small Steel flywheel w/metallic 5.5" single disk clutch, 240Z water pump with Nismo large degreed dampener - Tested, Ready to go.............................. SOLD
13 X 7 Keizer 3 piece wheels......4 X 4 1/2" 3" Backspace...Set of 4. Super lightweight............................ SOLD
13 X 7 Revolutions ....4 X 4 1/2" 3" Backspace...Set of 4.............Super lightweight & Classic................. SOLD
44 MM Mikuni's - Original PHH-2's like on the early roadster. Excellent shape, completely rebuilt, ready to go.. SOLD
44 MM Mikuni's - TAPER BORED comp-prepared completely rebuilt comp jetted - 41mm venturis, choice of jetting
excellent shape, ready to go... S ee Pix ........ See Pix .......... See Pix ................................................................ ... SOLD
44 MM Mikuni's - Virtually new, used once - excellent shape, ready to go................................ See Pix. .......... SOLD
BRAND NEW OLD STOCK U20 Roadster setup with NOS Unused Mikuni/ Solex 44's on Roadster manifold.
Ready to bolt on and go. 75mm horns. Original OEM linkage, standoff. OEM Insulators and water tubes. This setup is 100% New Old Stock Datsun Roadster stuff!! Make that Roadster restoration 100 point! ................................ see pix ..... see pix ..... see pix ..... see pix ..... see pix ...... see pix ...... see pix ...................... SOLD
MSA Short shift kit for the Z style 5 speed. Also fits the direct drive comp boxes. Complete with all hardware and used very little. Shortens shift throw by 60%................................................................................................... SOLD
V912 SSS High Compression head from factory (11041-U0600A) 1 1/2" ports 42MM intakes and 35mm exhaust, setup with springs , Slightly smoothed ports, uncut Block surface - Do a valve job and you are ready for cam and cover.................................................................... $ 750.00... .. SOLD
Datsun Comp Oil spray bar for 4 cylinder, brand new with instructions, tee fitting and hose.......................... SOLD
Accusump 3 quart, Barely used before switch to drysump . Complete with hoses, brackets, ball valve, gauge.... SOLD
Mallory dual point Vacuum advance distributor, great shape, for L-series 6 cyl.. see pix ..see pix ..$125.00 . .. SOLD
BRE NOS Filter blockoff adapter, complete with center tube adapter and cross-drilled bolt for safety wire. This is the original you see in the good books. Fits all L-series motors....... Brand New Nismo 8 hole adjustable timing sprocket (13024-E4621) -12 to +3 degrees in 3 deg steps.. see pix...... see pix.....SOLD
Tilton 6 bolt Aluminum flywheel Std diameter w/dual disk Quartermaster 7 1/4"clutch, great shape .............. SOLD
QM Lightweight Steel Flywheel, Std diameter 6 bolt w/dual disk 7 1/4" V-drive QM clutch,xlent ...$ 550.00 .. ... SOLD
Datsun Comp Oil spray bar for 4 cylinder, brand new with instructions, tee fitting and hose................................ SOLD
Ready to bolt on and go. 75mm horns. Original OEM style linkage and standoff. OEM Insulators and water tube. Make that Roadster restoration 100 point!......see pix.....see pix.....see pix. . .. .. SOLD
40/44 mm HKS JDM Long triple sidedraft manifold for Z-car ......................................... SOLD
R180 4.11 LSD...brand new LSD ass'y from Nissan Motorsports..Reshimmed from factory setting....Ready to go with U-joint or Tripod-joint axle flanges, your choice....................................................................................... .. SOLD
Brand new NOS Interpart T/C rod kit for 510/610 & Z-car all original with doc's......See pix.................................................................. .. SOLD
Tilton 5 1/2" Triple Plate OT-III Clutch - w/o disc/flywheel - BRAND NEW.................................................... .. SOLD
HKS 225mm 6 bolt Steel Flywheel Only 11 lbs! JDM Brand New - NICE!!................................................. .. SOLD
40/45 mm Mikuni Short triple sidedraft manifold for Z-car w/ linkage............................................................... SOLD
1 pair of 2 door 510 rear vent windows in excellent shape............................................................................ SOLD
Nismo narrow groove pump pulley # 21051-E4621, matches small diameter damper below..see pix .....See Pix .................................................................................. SOLD
R180 4.11 Open Diff complete w/ U-joint side flanges................................................................................ .... SOLD
Offenhauser Dual Port/Dual Plane downdraft manifold for L16/L18/L20B Brand new in Original box............... .... SOLD
Competition Prepared 44 Mikuni's TRIPLES on long runner ORIGINAL Nissan/Datsun Comp Manifold with insulators & horns. New jets, new jet blocks, Comp Jetted et al FOR 6 CYLINDER Z-CARS. Beautiful original Datsun Comp Manifold perfect for that Vintage/Historic Restoration or race car..........see pix..........see pix.. .... SOLD
Virtually new Competition Oil Pump (15010-A1115) W/external adjuster above..................................... .... SOLD
44 MM Mikuni's - Virtually new, used once - excellent shape, ready to go................................ SOLD
1 Set of 4 Libres, 13 X 7 - 4 on 4 1/2" Great shape - Sold only in sets of 4......see pix ....... . .............. . SOLD
A complete Datsun Comp/Tilton PL510 front strut setup w/BIG brakes: A custom built Tilton strut utilizing original Datsun Competition department struts, shortened with adjustable spring perches welded on. Custom Tilton caliper mounts Tig welded, no adapters necessary. Utilizes Z calipers modified for use with ZX vented rotors on custom built Tilton aluminum rotor/bearing hubs with extra long Moroso 1/2-20 studs. Calipers rebuilt with new seals, rotors turned true. Rotors modified to prevent warping under extreme heat. Fresh bearings, races, and seals, all new hardware. Uses all standard parts from 510, Z-car and ZX. All you need are strut inserts, pads and springs. A sweet setup for that 2.5 Vintage racer or todays race cars. Ready to go!............................................see pix.....see pix.....see pix.................................. . SOLD
Roadster 5 Spd in Std Ratio's w/L-bellhous, Steel Porsche syncro, w/shifter, great shape, low-time, very clean. . SOLD
New Turbo Oil Pump (15010-S8000) W/external adjuster above............................................................... . SOLD
Aluminum 5 bolt Tilton flywheel, 200mm w/new friction surface - good shape..................................... ........ . SOLD
A87 SSS High Compression head from Slovers Porting Service 1 1/2" + ports, 44MM intakes and 35mm exhaust, setup with Isky springs & retainers - Very nicely done, valve job and you are ready for cam and cover.................. . SOLD
Powder Coated early Z Damper 2 row w/bolt & washer................................................................................ ...... SOLD
A set of 4 N85 rods-6" long for L20B/Z22, floating pin/unbushed, SPS bolts, Magged & balanced.............. ..... . SOLD
44 mm JDM Hayashi Long triple sidedraft manifold for Z-car w/linkage, nice...........see pix ....See Pix ........ . SOLD
Z-car HD/performance Clutch and disk for 225mm flywheels with throwout bearing and sleeve BRAND NEW.. . SOLD
Set of 4 Panasport Racing wheels in 13 X 7, 4 on 4 1/2 B.C., 4" backspace, beautiful shape................... . SOLD
Roadster 5 Spd in Std Ratio's w/L-bellhous, Steel Porsche syncro, Alum shift bushings w/shifter, great shape.. . . . SOLD
R180 - 4.875 Ring & Pinion only, BRAND NEW, never setup.....38100-U3706..................................... ..... .. SOLD
Mallory dual point mechanical advance distributor, great shape, TACH DRIVE for L-series 4 cyl..see pix.. . SOLD
Tilton 5 1/2" Double Plate OT-III Clutch - w/o disc/flywheel - BRAND NEW............................................... ...... .. SOLD
R180 4.11 Open omDiff cplete w/ U-joint side flanges.............................................................................. ...... .. SOLD
Complete GT4 Nissan L16 - Alderman Race motor. 13:1 compression W/Electromotive Crankfire HPV-1 included. W53 Slover head with hi-lift asymmetrical Electramotive L4 cam w/Nismo degreed cam sprocket, DPR cam oiler spraybar, Turbo Head Bolts, Arias domed Pistons, Total Seal rings, worked rods w/ARP bolts, Diesel Main bolts, Small Quartermaster Steel flywheel w/ 7.25" single disk clutch, 240Z water pump with small degreed Gilmer drive mandrel and Dry sump pan/pump setup. Wrap around header not included. Can be converted to wet sump Comp pan and pump. Your choice. 0 Hours since freshening, ready to go............... ..........see pix......see pix............... ...... . . SOLD
QuarterMaster 6 bolt 94 tooth reduced diameter 6 pound Steel Flywheel for 7 1/4" clutch.......................... ...... . . SOLD
Stahl Race header for 510. #24 std. with 1 3/4" diameter tubes - good shape.................................................... . SOLD
QuarterMaster 6 bolt 94 tooth reduced diameter 6 pound Steel Flywheel for 7 1/4" clutch..................... .... ...... .. SOLD
QuarterMaster 7 1/4" Clutch single disc complete,w/o flywheel or discs................................................... .... ...... .. SOLD
Tilton Super Starter, gear reduction with offset nose for reduced diameter 94 tooth flywheels....see pix..... 40 MM Mikuni's - Completely rebuilt, excellent shape, ready to go................................................................ . SOLD
Nissan Comp Manifold for dual sidedraft 44's or 45's...................................................................... ...... .. SOLD
Brand new Flowmaster muffler - aluminized # 43041 3" in/out................. see pix.....see pix......see pix....................................................... . SOLD
Stahl Race header for 510. #24 std. with 1 3/4" diameter tubes - great shape........see pix........ . SOLD
New Wiper motor for 510 # 28810-N2802.......See pix....................................................... . SOLD
40 mm Cannon Long triple sidedraft manifold for Z-car w/ linkage.................................... $ 250......... ... . ... SOLD
Nismo Small race damper crank pulley - degreed # 99996-E4620.............................................................. ... SOLD
FJ20 Dual Sidedraft 44/45 Manifold..................................................................................................................... SOLD
Rebuilt 44's Mikuni's on Long Gerolamy Nissan Comp Manifold with insulators, no horns, no linkage............ . SOLD
Pair of 'glass front fenders BRE flared - Fair shape, need small repair............................................................. . SOLD
Option #2 Direct Drive Tranny W/Electramotive 1.90 1st gear setup.....Great Shape................................. ........ SOLD
Option #1 Direct Drive Tranny...........Great shape.............................................................................. ........ SOLD
Electramotive custom fabbed straight cut 1.90 1st gear set for Direct Drive Comp tranny's................ SOLD
Nissan Comp Manifold for dual sidedraft 50's....................................................................see pix ..... See Pix. .... SOLD
50 MM Nissan Comp Long Runner manifold w/prepped insulators and center pull linkage for above................ SOLD
Cannon Gooseneck Long Runner Dual sidedraft manifold for 40, 44, 45 mm carbs, 1 available.......................... SOLD
Nissan Comp Large Degreed Front Dampner # 99996-E1060E........see pix.............................. ........ ... SOLD
A set of 4 NEW Venolia Forged Domed Pistons for L20B (1mm over) 99996-K1010B no pins, no rings........ ..... ... SOLD
44 MM Mikuni's - Brand New, never used....................................See pix.......................... ... SOLD
Aluminum 6 bolt flywheel, 200mm with good Atsugi Roadster pressure plate and Solid disk - ready to go........... ... SOLD
Z20, Z22, Z24, Naps-Z Dual sidedraft manifold w/linkage................................................................................. ... SOLD
45 MM webers - rebuilt - no manifold............................................................................................................... SOLD
R160 - 4.375 Ring & Pinion only, Break in time only, looks excellent................................................................... SOLD
Mikuni Air filters - Billet filter mounts w/ K&N filter elements. Fit 40's or 44's or 45's........................... See pix...... SOLD
40 MM Mikuni's - Not competition prepared but recently rebuilt - excellent shape, ready to go.....SOLD
K&N filters w/stamped steel housings. Fit 40's or 44's or 45's......................................................................... .. SOLD
Competition Prepared 44 Mikuni's on long Gerolamy Nissan Comp Manifold with modified insulators & horns...... . SOLD
Tilton 6 Bolt Aluminum Flywheel - 200 mm used, excellent shape - modified to accept Tilton 7 1/4" OT-II metallic clutch available with complete clutch setup in either single plate configuration or twin plate configuration... See pix1...... See Pix2..Dual Plate complete w/ discs.................. ... SOLD
A set of 6 stock Rods L16 or L24 fully prepped with chevy bolts, polished, bushed, balanced Magnafluxed............ ... SOLD
Cannon 40mm Long runner manifold with linkage - combine with some carby's above for a great system...See pix... SOLD
Isky Z196 Race Cam .530"Lift/290 Duration with matching rocker arms and card............................................ ..... SOLD
Nissan Comp Large Degreed Front Dampner # 99996-E1060E................................................................... ..... SOLD
44 MM Mikuni's - Not competition prepared but recently rebuilt - excellent shape, ready to go.....See Pix............. ... .. SOLD
SR20DET JDM Turbo Exhaust manifold - will fit S13 or S14 turbo retrofit..........................................See Pix... ... .. SOLD
L Series 4 cyl fabricated turbo Exhaust manifold - Nicely done - bolts right up - Garrett T25 turbo flange...see pix. .. .. SOLD
Garrett T25 Turbo for either application above - excellent shape.....................................................See Pix........ ... .. SOLD
44 mm TWM #0030 triple sidedraft manifold for Z-car w/ linkage....................................See pix...................... ... .. SOLD
V912 SSS High Compression head from factory (11041-U0600A) - NEW - NEVER used. 1 1/2" ports 42MM intakes and 35mm exhaust, setup with springs - Ready for cam and cover........................................................................ ..... SOLD
Standard Roadster 5 speeds.............................................................................................................................. .. SOLD
13 X 7 Slotted Aluminum ARE wheels to fit Datsun 4 on 4 1/2 Z-car or 510....................................Set of 5 .. .... SOLD
A set of 4 NEW Wiseco Forged FLAT TOP Pistons for L16 (1mm over)w/valve reliefs, locks & pins, no rings...... SOLD
BRAND NEW Original/early SSS Single point distributor Model # D411-88 w/cap & rotor.......... See Pix.... ... ... SOLD
Dual 40MM Weber Sidedrafts rebuilt w/horns on Warnerford manifold w/heat shield - Mechanical linkage for 510 READY for
GProd or street. Italian castings, Complete ready to go.....................................................See pix..................... ...... ... SOLD
14 X 6 American Vector Aluminum wheels to fit Datsun 4 on 4 1/2 Z-car or 510.......................................... ... SOLD
Tilton 6 bolt Aluminum Flywheel - 10 lbs BRAND NEW Tilton Part # 50-029 w/original Tilton docs, 200mm.... ... SOLD
2 Sets of (4) NISMO SI 44mm (1.73") Intake Valves p/n 99996-N1100 for L-series Heads............................ ... SOLD
R180 - 4.11 open diff - slip in side shafts - add $ 50 for conversion to bolt-on style side shafts........................... ... SOLD
Early SSS head - Casting number 219-1 1/2" ports - Closed Chamber- Excellent shape, no valves/cam...see pix ....................................................................... SOLD
Cannon 40MM dual sidedraft manifold w/linkage................................................................................................ SOLD
Pair of 45 MM Weber DCOE, Italian castings, Linkage between them, manifold not included, Great Shape......... SOLD
A Set of 3 (Z-car)Brand new 44mm Mikunis w/long horn and linkage Nismo# 16010-E4620 w/o manifold......... ...... SOLD .
Electromotive Competition Intake Manifold - Long Runner 44 MM (new)....see pix. .. SOLD
510 short tailshaft 4 speed - Race Prepped by Leitzinger for ITC Racing with extra deep oil sump std. ratios.......... SOLD
GT Car Brake setup:
1 Pair JFZ Mini GN Single (just like Wilwood Dynalite Single $ 85.ea new)for rears, uses HB104 pads
1 Pair JFZ Mini GN Dual (just like Wilwood Dynalite $ 115.ea new)for fronts, uses HB100 pads.... ........ SOLD
Autometer Monster Tach 5" 9000 RPM with memory recall model# 6809 Work's Perfect!............... SOLD
New Roadster Driveshaft - slip joint style with bolt flanges on both ends - use to install above in 510.................. ....... SOLD
Brand New 210 Head for L16. This is the "TK" casting sought after for IT racing. Unused/uncut with valves, cam, rockers et al. Completely setup and ready to bolt on. "TK" casting was late availability on L16's and a bit smoother casting all the way thru with slightly bigger than 1 1/8 ports and improved oil passages. ALL ITC LEGAL. ........... ..... SOLD
Datsun Comp rear racing springs (not coilover) - 8 inch overall, 700 Lb/in rating.
Seriously lower and stiffen car............................................. SOLD
KONI adjustable Rear Shocks (not coilovers) used- good shape................................................................. SOLD
Complete UNUSED Suspension Package for Street/Autocross/IT Racer:
Pacesetter/Turn Six Package includes front and rear springs that are 20% stiffer and lower car about 1 1/4" all around. Front 7/8 diameter SwayBar with Polyurethane Mounting bushings, Rear 3/4" SwayBar with Polyurethane Mounting bushings, OEM Documentation and hardware. All powder coated yellow............. SOLD
ARE Dry Sump pan w/-12 fittings for 6 Cylinder L-series - excellent shape ($380 new + fittings). Pix 2 ........ SOLD
Bronze Button Clutch Disc - Solid Hub 200mm BRAND NEW Nismo Part # 99996-D3040....SOLD